Support

  • How to install
  • Referential data
  • Technical terms
  • E catalogue

How to install the led panel light (Suspended Installation)
 
1) Prepare accessories and tools.(The quantity of accessories may be different for different dimension of lamps, this instruction is based on SP2-6060)
led panel light install a1
 
2)Put the steel wire through the “bullet head” screw nut and wire locker.
led panel light install a2
 
3) Mark the dri ll hole on the cei ling according to the drill hole position template, and drill the proper hole for number⑤ Bolts.
led panel light install a3
 
4) Put the bolt in the hole, using screw to install the “T” shape screw nut.
led panel light install a4
 
5) Put the steel wire through the “T” shape screw nut, and get the steel wire out from the hole on the “T” shape screw nut, fix the wire locker.
led panel light install a5
 
6) Fix the driver on the back of the panel light with adhesive tape or screws, and connect the driver to the panel light.
led panel light install a6
 
7) Screw the “bullet head” nut to the screw on the back of panel light.
led panel light install a7
 
8) Adjust the length of each steel wire by wire locker, to keep the panel light in balance and stable.
led panel light install a8
Click to view more installation:
1.Suspended Installation
2.Surface mounted installation
3.Recessed installation (for gypsum plaster ceiling)
4.Recessed installation (for cut out ceiling)

Comparision of office bulidings’ illuminance standard value (Unit: lx)

Room or Site

CIES 008/E

-2001

USAIESNA

-2000

GermanyDIN 5035

-1990

RussiaCHиП

23-05-95

ChinaGB50034

-2004

Ordinary offices
500
500
300
300
300
Advanced offices
500
500
Meeting/reception rooms, Front desk

500300(reception)

300500(important)

300

200300(front desk)

300
Business halls

300500(reading,writing)

300
Designing rooms
750
750
750
500
500
File arrange,copy rooms
300
100
400
300
File store rooms
200
75
200

 

Comparision of commercial bulidings’ illuminance standard value (Unit: lx)

Room or Site

CIES 008/E

-2001

USAIESNA

-2000

GermanyDIN 5035

-1990

RussiaCHиП
23-05-95

ChinaGB50034

-2004

Regular shops

300(small)500(big)

300
300
300
300
Advanced shops
500
Regular supermarkets
500
400
300
Advanced supermarkets
500
Cashiers
500
500
500

 

Comparision of resident bulidings’ illuminance standard value (Unit: lx)

Room or Site

CIES 008/E

-2001

USAIESNA

-2000

GermanyDIN 5035

-1990

RussiaCHиП

23-05-95

ChinaGB50034

-2004

Living normal activitiesReading writing

300(short time reading)500(long time reading)

100
100
300

Bedroom normal activitiesReading, writing

300(short time reading)500(long time reading)

100
75
150
Dining rooms
50
150

Kitchen normal activitiesoperation

300(general)500(hard)

100
100
150
Washrooms
300
50
100

 

Comparision of office bulidings’ lighting power density (Unit: W/M2)

Room or Site

USAASHRAE/IESNA

-1999

RussiaМГСН 2.01

-98

ChinaGB50034

-2004

Ordinary offices

11.84(Closed)13.99(Open)

25
11
Advanced offices
18
Meeting rooms
16.14
11
Business halls
15.07
55
13
File arrange,copy rooms
25
11
File store rooms
8

 

Comparision of commercial bulidings’ lighting power density (Unit: W/M2)

Room or Site

USAASHRAE/IESNA

-1999

RussiaМГСН 2.01

-98

ChinaGB50034

-2004

Common shops
22.6
25
12
Advanced shops
19
Regular supermarkets
19.4
35
13
Advanced supermarkets
20

 

Comparision of resident bulidings’ lighting power density (Unit: W/M2)

Room or Site

USAASHRAE/IESNA

-1999

RussiaМГСН 2.01

-98

ChinaGB50034

-2004

Living rooms
20
7
Bedrooms
Dining rooms
Kitchen
Washrooms

Luminous flux: is the measure of the perceived power of light, unit is lm.

 

Luminous intensity: is a measure of the wavelength-weighted power emitted by a light source in a particular direction per unit solid angle, based on the luminosity function, a standardized model of the sensitivity of the human eye. The unit of luminous intensity is the candela (cd).

 

Viewing angle: light emitting diode lighting angle is the scattering angle of the light rays, it is mainly controlled by the diffusing powder during the production of LEDs. There’re three kind: 1. Direct type: with beam angle of 5-20 degree or even smaller 2. Strand type: with beam angle of 20-45 degrees 3. With beam angle of 45-90 degrees or even higher.

 

Luminance: is a photometric measure of the luminous intensity per unit area of light travelling in a given direction. It describes the amount of light that passes through or is emitted from a particular area, and falls within a given solid angle. The unit for luminance is candela per square meter (cd/m2).

 

Illuminance: is the total luminous flux incident on a surface, per unit area. It is a measure of how much the incident light illuminates the surface, wavelength-weighted by the luminosity function to correlate with human brightness perception. Similarly, luminous emittance is the luminous flux per unit area emitted from a surface. Luminous emittance is also known as luminous existence. In SI derived units these are measured in lux (lx) or lumens per square metre (cd*sr*m2).

 

Color temperature: The color temperature of a light source is the temperature of an ideal black body radiator that radiates light of comparable hue to that of the light source. The unit of absolute temperature, the Kelvin, having the unit symbol K.

 

Luminous efficiency of a light source: is a measure of how well a light source produces visible light. It is the ratio of luminous flux to power. The total power (electric power, chemical energy, or others) consumed by the light source total luminous flux is the luminous.

 

Luminous efficiency of lamps and lanterns: is the result of the total luminous flux of a lamp or lantern divided by the total power consumption of the lamp or lantern, is one of the important index of energy saving performance of a lamp or lantern. The unit is lm/w.

 

Color rendering index: is a quantitative measure of the ability of a light source to reproduce the colors of various objects faithfully in comparison with an ideal or natural light source. Numerically, the highest possible CRI is 100, for a blackbody (incandescent lamps are effectively blackbodies), dropping to negative values for some light sources.

 

Glare: is difficulty seeing in the presence of bright light such as direct or reflected sunlight or artificial light such as car headlamps at night, Glare is caused by a significant ratio of luminance between the task (that which is being looked at) and the glare source.

 

Lighting power density: technically represents the load of any lighting equipment in any defined area, or the watts per square foot of the lighting equipment, the unit is w/m2.

 

IP degree: sometimes also interpreted as International Protection rating, classifies and rates the degree of protection provided against the intrusion of solid objects (including body parts such as hands and fingers), dust, accidental contact, and water in mechanical casings and with electrical enclosures. It is published by the International Electrotechnical Commission (IEC).

huapu-led-light-catalogue-2014.pdf
Catalogue-2014
2.24 MB
LED panel light catalogue2013
Catalogue-2013
2.97 MB
LED panel light catalogue2011
Catalogue-2011
2.13 MB
LED panel light catalogue2010
Catalogue-2010
4.03 MB
LED panel light catalogue2009
Catalogue-2009
4.18MB